Blog Update

Today ruby and I got our catapult finished. It was really good. We started off by adjusting the axel at the top so that the dimensions fitted the trebuchet. We then worked on attaching the cup to the end of the propellor. We first tried making a stand for it but then Mr ward said it should be fine how it is. With the help of Mr Ward we then screwed holes in the bottom and this took a bit of adjusting so that the Asclepius in which the wheels are to rotate off can rotate. But after that, it was just a press fit of the wheels and then the catapult was ready.

First using a 1kg weight that was hooked to our swing, we propelled the ball from outside the classroom and it reached about the drains. We then advanced and added a 2kg weight and the ball went further. I think next lesson we will just reinforce the pole at the end closest to the axel because the wood is beginning to split. But after that then we will do our recordings and I will video it so I can not step by step, the process in which the catapult takes.

Blog Update

Today ruby and I got straight into the workshop. But before we did that we made sure that we could do tomorrow lunchtime to get more of it done so that we had plenty of time to get the whole assessment done before the due date. 

We started off by finishing the extenctions and support to the top of the A-Frame, which glued well. We then got Mr. Ward to help, and Ruby drilled a hole in our sling, this was a factor that made it line up with the bottom of the A-frame, not the full catapult end. This would allow us to have more force pulling down on the weight end of the sling. 

Mr Ward then drilled a hole through the other A-frame and we managed to get the whole top part lined up with not too many issues due to the un-allignment of the frames. 

I then drilled a hole through the bottom of the sling where we would hang our weight off. I was nervous but I was able to do it fairly well and it was good that I was made to do it under controlled conditions so it was harder for me to do something wrong. I also hammered the rod through that Mr Ward measured out to be a press fit and then I sanded it smooth. 

Ruby then had the idea to cut a wheel in half and use it for the pin holder. It looks really good but we will finish it later when we know the full dimentions of our cup. 

Blog update

Today we glued the two a frames to the plank connecting them at the bottom. Once we did that, mr ward pointed out that our a frames were not even because of a tilt or not properly measured middle rod in the a frame. Mr ward started by drilling a hole through the top but then it snapped. Mr ward then showed how to add the reinforcements I the side so we are working on that now

Design

Today in design mr ward was away do we did theory. I managed to put the timeline onto an actually timeline and I wrote out the definition for PE and got all the rest of the assessment ready. So when I have the information, I can just write it in.

Blog update

Today we went ahead with making the A frame. After pushing and gluing the vertical side into the horizontal piece of wood that utter brilliantly.
we measured up the wooden frames for the long diagonal frame. Though we measured it out to what we thought should be perfect - it didn't end up that way. So when we glued one of the sides on we had to add a thinner peice of wood to it so it would e more secure.

Blog update

Today ruby and I ruled up (this time because last time it was a last minute rush because it was a mistake in progress). So we added another block of wood across the frame for the other frame. We also reinforced bits and prices with nails so that te Redfin is up to date. We measured up and cut one of the other joints to the frame and it fitted perfectly. We went to the other side but didn't have time to check it fits.
Uploaded are the pictures from lat lesson

Blog Update

Today in design Ruby and I sanded down or connectors and glued them in. Now the connectors din't fit right so we had to nail them in at the same time. This was an unplanned process so the first nail ended up coming out the other side, rather than through the center.
However by the end of the lesson we had all the - for the A frame set into both frames and for the first, we also secured it with another piece of wood (glued) to keep it together and to keep it straight. We also made reinforcements to the tops of both A frames and the bottom of one of the A frames. I have my time line ready for my assessment, however I could not find the full assessment schedule on blackboard again so I have emailed Mr. Ward regarding that matter.

Blog Update

Today Ruby was here and we continued with our - of the A frame. By the end of the lesson we had the two sides for each glued together so they can be attacted properly to the fame. This lesson I also traced out reinfrocements for the top of the frame. What I have planned to do before we finish the A frame is to

1. enforce < > in with screws
2. Renforce base with pva glued wood
3. drill hole for the axel to pass through

etc...

i also broke the drill saw today and learnt to saw a few millimeters away from the cut line and then sand the rest (this has been really helpful)

I have started my timeline

Lined Timeline of Trebuchet

·    3-5bc: The Chinese were thought to have invented the first trebuchet (Huihui Pao) which, in design, was very similar to a sling, with 15-45 men used as the counterweight.

·    300ad: Greek and Roman (Soldiers of Piliip of Macedonia created their ballistas (a different form of trebuchet) which design was similar to a crossbow and is thought to be the primiary inspiration for the catapult/trebuchet. Difference is that ballistas used two wooden arms rather than one

·    350ad: Romans created mangoles which was similar to the ballistas however they only had one wodden arm enabling them to hurl stronger and sharper objects at a greater speed.

·    965 c:  First recorded hand-trebuchet in Greece.

·    6^th c:    “balliustae revolving in both directions” this appeared in Byzatium

·    12^th c: French created the trebuchet which turned to be the true siege engine of mass destruction and at the time it’s power and force was unmatched. It used only one wooden arm which rested on a pivot point. Because the point was used as a leaver, the object could be hurdled at a much greater spped and strength.

·    Middle Ages: catapults were the major siege weapons because of there extreme effectiveness in battles. As history went on, the catapult evolved, capable of more damage. The catapults were used to fire projectiles (as much as three hundred pounds) as well as bodies of people and animals who have died of a disease, into the castle walls.

·    1097:   Emperor Alexios I Kommenos in the Siege of Nicaea was reported to have invented a new form of trebuchet.

·    1211ad: The siege of Castelnaudry was the first time that a trebuchet is mentioned.

·    1124:   The Crusaders used great siege engines for the Second Siege of Tyre in Lebanon. It is believed that these great siege engines were counterweight driven trebuchets.

·    1187:   The first pictorial evidence of counterweight driven trebuchets appeared in a military manual written for the military leader Saladin.

·    1191:    for the siege of Acre two large trebuchets were used by Philip II

·    1268   First recorded Chinese counterweight trebuchets in the Mongol siege to Francheg and Ziangyang.

·    1304:   A giant trebuchet named “warwold” was created for the English army

·    1475:   The introduction of gunpowder caused less need for trebuchets over cannons however the trebuchet was still used in the siege of Burgos

·    1779:   When British forces were defending Gibraltar the constructed a trebuchet because their cannons were unable to fire long enough.

Blog Update

Today Ruby was away so I worked by myself in the workshop today. I started straight away and continued working on the materials from last term. Today I ruled up more connections to go across the middle of the A-Frame. To ensure stability within the frame we are having two sides to this connection. So this lesson I ruled up the markings and used the drill saw and started cutting them to shape.